|
ONLY $29.99
RETAIL $39.99,SAVE $10.00
The SeaCURE mouthpiece was created by an Orthodontist for total diving comfort. This mouthpiece is designed so you can heat it and form fit it to your mouth, giving you the ultimate custom fit. The primary purpose of the SeaCURE is to eliminate jaw fatigue and TMJ symptoms, relieving the pain and pressure that many people have while diving or snorkeling. It is also very good for people who bite through their mouthpiece.
Because of the personal nature of this item, it is non-refundable and non-exchangeable. If you have any questions regarding fit, please call for consultation.
Choose SeaCURE fit by size: (Alphabetical listing available by clicking here)
SeaCURE I - fits standard orifice regulators that have a conventional mouthpiece retention lip.
Apollo; Bridgestone; Coral; Dacor (new pacer model; not older pacer); Beuchat (VS-3,4&5); Cressi-sub; IDI; Parkway; Halcyon Rebreather; Pro Sub (Avalon); NDS; Nemrod, ; Scuba Pro; Seac; SAS; Sherwood (most early models/Brut/Magnum II/Oasis/Pre 1992 Blizzards); Tabata/Tusa 500 Series; Early Metal US Diver Models; and other standard size orifice regulators.
(SeaCURE cannot be used on AERO model Dacor because of holes in body of mouthpiece orifice)
SeaCURE II - fits intermediate size air orifice regulators.
Apex; Atomic Titannum; Beuchat (VS-6&10); Chiaro; Mares newer model but not on Mares MR12II, III, IV or V); IST; Ocean Edge; Tekna; Oceanic; ProSub (larger size); Seaquest (not air source);Sherwood Maximus/Oasis 2/1992; Newer Blizzard; New Maximus (requires Professional Model only, the diver can grind one side of the internal core of the mouthpiece to maintain and venturi effect); Zeagle; and other intermediate size orifice regulators.
Poseidon/ Sherwood Ultima - While SeaCURE is not designed to fit Poseidon of Sherwood Ultima, many divers are now using a Pro Model SeaCURE II with these regulators. It takes considerable extra effort and strength to mount SeaCURE II, but it will go on the plastic models, not on early metal units. (Never place the regulator end of SeaCURE into boiling water but only warm tap water on it for 2-3 seconds and a small amount of soap or spit on the orifice may also help ease it on. No other lubricant should be used. DO NOT USE SPORT MODEL ON ANY POSEIDEN OR SHERWOOD ULTIMA (IT WILL SPLIT))
SeaCURE III - Fits US Diver Plastic Regulators, new Seaquest, Genesis, & SeaMech
US Diver regulators do not have the conventional retention lip on the mouthpiece orifice common to all other regulators and therefore no other SeaCURE model should be used on Plastic US Diver regulators.
Snorkels - SeaCURE fits removable mouthpiece snorkels on the market. The SeaCURE model that fits is noted where known.
Amico (I); Cressi-sub (I); Dacor 3 models (I); Netex (I); Ocean Reef (I); Reef Buddy (I); Tusa 500 Series; IST; Parkway (II); Pic (II); Techisub (II); Ocean Master, Dry2000 (III); ProFlo SQC (III); Trident; US Diver (III).
Not listed above If possible, try both SeaCURE I and SeaCURE II on the unit in question to see which fits. Otherwise, simply measure the retention lip on the air orifice of the regulator. The results of a recent survey of regulators indicate that almost all fall into two general sizes with some in each group being slightly larger or smaller than the average.
Standard Lip - (1-1/4" x 3/4") takes SeaCURE I
Oversize Lip - (1-7/16" x 7/8") takes SeaCURE II
Choose size below.
|
